小林设计素材网 客服QQ:178308054 Email:178308054@qq.com 机械设计资料 | 相信专业,相信小林 | 小林机械资料网竭诚为您服务!
首页 | 工艺夹具 | 数控编程 | 注塑模具 | 冲压模具 | 机械机电 | 土木工程 | 采矿通风 | 其他专业 | 购买流程 | 信誉说明 | 付款账号 | 加盟
     
您现在的位置: 主页 > 冲压模具 >
设计名称
滤油器支架模具设计
设计编号
e101
设计软件
AutoCAD, Word
包含内容
见右侧图片
说明字数
20000字
图纸数量
见右侧图片
推荐指数
较高
价格:
价格优惠中
整理日期
2013.09.26
整理人
小林
购买流程
<查看如何购买本站设计>
设计简介

设计描述:

Word版说明书一份,40页,20000字左右.

外文翻译一份

CAD版本图纸,共25张:

 

滤油器支架模具设计

摘要

本说明书主要是阐述了有关滤油器支架模具设计的基本过程和其主要计算。全文共由四章组成,他们的内容如下所述。
第一章是设计滤油器支架模具的工艺方案的确定,主要根据所给制件特点加以分析,设计出合理的模具,这里共设计出三套模具。第二章是落料拉深复合模的设计,其中包括一些典型结构的选择和一些非标准零件的设计。第三章是冲孔切边复合模的设计,包括各种模具零件的选择和一些零件尺寸的计算。第四章是弯曲翻边复合模的设计,此章除了沿用了相关类似模具结构外,还进行了简单的计算和零件设计。
鉴于本人的水平所限,在设计中肯定有不足之处存在,也可能有错误出现,恳请评阅老师和各位读者包涵并且批评指正。


关键词:   模具    复合模    零件

 

 Abstract

This paper is main elaborates the basic mould design course of the sieve   oil implement’s bracket,and expounds the main calculation course for it.
There are four parts in this paper, their content as follow.
The first chapter is settling the project of the mould design’s craft to  the sieve oil implement’s bracket. It main contains the analysis of the sieve oil implement’s bracket’s characteristics. Make sure design three suitable moulds. The second chapter is the design of the blanking and drawing compound dies. It contains the choosing of the typical framework of the dies. The design
of some accessory. The third chapter is the design of the piercing and trimming compound dies. It contains the choosing the caculation of accessory. The forth chapter is the design of bending and flanging compound dies. In addition to using the similar framework of the dies, it contains some calculation and design of accessory.                                                                    
In view of my limited knowledge,I could have made some mistakes in this paper, I wish my teacher and the readers could help me correct it, thanks!


Keywords:  mould      compound dies      accessory


目录

第一章  工艺方案的确定………………………………………………………………4
第二章  落料拉深复合模的设计………………………………………………………7
第三章  冲孔修边复合模的设计………………………………………………………19
第四章  弯曲翻边复合模的设计………………………………………………………30
毕业设计总结……………………………………………………………………………39
参考文献…………………………………………………………………………………40

 

第一章  工艺方案的确定
一   制件工艺分析

    滤油器支架结构较为简单、材料为08Al,厚度为1mm。成型工艺包括落料拉深、冲孔修边、弯曲翻边三部分。 制件上的拉深为浅拉深(最大处也只有4.4mm)可一次拉深成型,同时制件结构对称,经计算满足冲压工艺要求。制件在进行冲孔、落料、修边时需要有必要的计算,之后才能确定凸凹模尺寸,这是设计时所必须的,这里体现了最原始的数据资料。在设计弯曲翻边部分时,要考虑到制件的弯曲回弹现象。

部分图纸
截图












说明:
如需了解本设计的具体详细信息请联系本站客服,说明看哪个设计(编号)哪个详细部分,我们将远程或截图给您观看.
机械毕业设计|论文
[要求PR≥2,百度收录≥1000页;联系QQ:178308054]
  • pass',
  • 最新选题目录 - 购买流程 - 信誉说明! - 付款账号 - 帮助中心
    声明:根据《互联网传播权保护条例》本站,小林机械资料商城,所列资料均属原创者所有,仅供学习交流之用,请勿转载并做其他非法用途。
    Powered by 小林机械资料商城 © 2013-2020 All Rights Reserved. 客服QQ:178308054
    喜欢www.xiaolinbysj.com,请告诉你QQ上的5位好友,多谢您的支持!